Fork Lift Safety

MAKE-IT-SAFE MONDAY

In fast paced working environments, safety is a very important priority.  Many of these fast paced environments involve the use of forklifts and can be very dangerous. According to statistics reported by the Occupational Safety and Health Administration (OSHA), they estimated that forklifts cause roughly 85 fatal accidents per year and injure roughly 35,000 others. Also, according to the Texas Department of Insurance, a loaded forklift weighs an average of close to 14,000 pounds. With this much weight, it’s not surprising how dangerous forklifts can be.

Many of these injuries could be avoided if the necessary safety precautions were taken. Proper training and use of forklifts is very important; trying to save a few seconds here and there is not worth risking the safety of yourself and others.

Three obvious but important safety tips to remember when operating forklifts or any factory machinery are:

1) Stay Focused. This might seem too obvious and simplistic, but it’s way too easy to get distracted and to mentally check out when doing something that you’re doing habitually. Focus is something that you should apply to all aspects of work, whether you’re using heavy machinery or just writing up reports.  Staying fully focused on the task at hand is a simple but effective way to stop avoidable mistakes.

2) Be Aware of Your Surroundings. This is an often overlooked safety precaution. Make sure you always look behind you the whole time you back up.  It must be more than just a quick glance before you begin to move. Surroundings can change between the beginning and the end of your travel space. Also, be aware of the location of pedestrians and slow down when you’re unsure of what is ahead. Knowing your surroundings helps you be prepared for what may lie ahead.

3) Don’t Cut Corners. From a young age we’re always told to obey the rules and do what we’re told. So it might seem unnecessary to say this. However, so often in the workplace you can be under pressure to get things done quickly and therefore feel the need to cut corners (physically and metaphorically). This can lead to going too fast and ignoring the rules you find unimportant, possibly causing accidents and potential injuries along the way. In the end cutting corners is never worth it and it’s best to realize that all safety regulations and rules have been put in place for a reason. If you suspect any corners are being cut or notice any unsafe working conditions, report it to the proper authorities immediately.

Thank you for your time and attention. Let’s make it safe this Monday.

Christopher Feigal

Demand Generation Specialist, Lift’n Buddy, a Southworth Company

Overexertion in the Workplace

MAKE-IT-SAFE MONDAY

Overexertion is one of the most common work-related disability injuries. Overexertion injuries involve working the body or one body part too hard, causing damage to the muscle, tendon, ligament, cartilage or joint. Overexertion can be caused be pulling, pushing or lifting with excessive force. There were more than 3.2 million overexertion injuries in 2009. Overexertion injuries account for almost 27% of workplace injuries in the US. These injuries are most common in young employees. In 2005, businesses paid a total of $12.7 billion in over exertion injury costs. In 2000 sprains and strains alone lead to $40 billion in lost productivity. 

Employers that want to minimize these costs should take a few steps to help reduce the risk of their employees overexerting themselves. Employers should make safety a priority for their employees. Employers should encourage employees to report all concerns about aches and pains. If aches are reported early they can often be healed early, and it will lower the risk of more severe injuries. When an employee reports an injury the employer should consider removing the employee from the task that is causing he/she an ache or pain. The employer should also make sure that their employees are never lifting something that is too heavy for them.

Employers should also teach all of their employees proper form and technique when it comes to lifting or moving an object. Teaching simple changes to an employee’s movements can prevent overexertion. The employer should make sure their employees are lifting with their arms and legs and not their backs. This helps by keeping movements slow and smooth instead of quick and jerky, and it reduces exertion. Also, when employees are lifting repetitively the employers should allow them a few short breaks to allow recover

Employers can protect workers by helping them stay healthy and fit. Many employers will offer discounts on gym memberships, nutrition programs, and exercise courses to help employees stay active, and lose weight. These discounts encourage employees to start exercise programs due to the affordability provided by their employer. These programs keep workers’ muscles strong, and help keep workers from getting winded easily on the job.

One of the best methods for employers to reduce the risk of overexertion by workers is by providing tools to make lifting easier. Employers can lower shelf height to make lifting easier for workers. The best height is from knees to shoulder height. This allows the workers to lift an object in an easy fluid motion, reducing risk of injuries among workers. Another effective way employers can reduce the risk of injuries in workers is to purchase technology that fits the needs of an employee.

Employers that take the initiative, and have taken action against overexertion injuries have seen a major reduction in costs spent on work place injuries. They have become aware of their inefficiencies and have stepped up to protect their employees.

Thank you for your time and attention. Let’s make it safe this Monday.

Lucas Wertish

Demand Generation Specialist, Lift’n Buddy, a Southworth Company

Hearing Loss

      MAKE-IT-SAFE MONDAY

Many people work in an environment that is very loud and protecting the hearing abilities of employees is very important.  Hearing loss naturally happens with age, but when people are exposed to excessive noises or loud sounds on a regular basis it could significantly increase the rate of hearing loss.  Being able to hear is something many take for granted, but it is important to remember to protect it the best you can.  Employees who are constantly under pressure of loud noises can lose their hearing and it is a usually a painless, progressive, and a very permanent processes.  When employees are experiencing hearing loss it can reduce their quality of life and affect their work and family life.  If an employee is experiencing hearing loss they may not be able to hear alarms, warnings or other auditory signals that are important for their job.  Excessive noise has also been associated with digestive problems, irritability, loss of concentration and even high blood pressure according to Occupational Health and Safety Online.  The noise that causes problems can come from numerous locations including manufacturing equipment, vehicles, construction equipment, power tools, aircraft and even lawn maintenance tools. 

Damage to your hearing cannot be repaired, but the good news is that it is preventable.  There three steps to help prevent hearing loss. 

1) Recognize that a noise problem may exist  

2) Evaluate the potential problem

3) Control the situation

Using this three step process could be very beneficial to the hearing of employees.  

Recognizing that there is a noise problem is the first step. Inexpensive decibel readers can be found online to accurately test for ear damaging noise. Even less expensive but less accurate smartphone apps can be found in the Apple and Android markets. It also helps to pay close attention to your surroundings, for example not being able to hear someone close talking to you.  It can be difficult to identify a problem if the noise is not constant.   If you notice a potential noise problem the easiest way to protect your hearing is to cover your ears with ear muffs and ear plugs.  Many employers recognize that noise problems exist and they will provide hearing protection. It is still important that you take precautions to protect yourself and make your employer aware of any unsafe work environments.  

Thank you for your time and attention.  Let’s make it safe this Monday.

Dale Bromenshenkel

Demand Generation Specialist, Lift’n Buddy, a Southworth Company

How to Survive Flu Season

MAKE-IT-SAFE MONDAY

With October just beginning, many are getting excited for the Halloween festivities, the changing colors of the trees, and Pumpkin Spice Lattes at Starbucks. While October is a favorite month for many, it is however, the beginning of the infamous flu season.

Flu season is marked in the United States as a time between October and May where there are often prevalent outbreaks of influenza, or known more commonly as “The Flu”. It is estimated by the Center for Disease and Control that US businesses loose roughly $10.4 billion dollars in any given year related to employees getting the influenza virus.

In order to stay clear of the flu this month and enjoy everything great fall has to offer, here are some precautions one can take to prevent the flu:

1. Always wash hands to defeat germs.
2. Get a flu shot from a local clinic or pharmacy.
3. Stock your medicine cabinet with any drugs you use, like pain relievers or decongestants. Don’t forget tissues, soap, and hand sanitizer.
4. Pay attention to symptoms – Symptoms of just the common cold are milder than those of the flu.
5. Take a sick day and relax – If you work yourself too hard when you have the flu this can delay your recovery.
6. Use throwaways – swap cloth hand towels with paper to prevent the spread of germs.
7. Drink lots of fluids – broths, water, sports drinks, and herbal tea are all excellent for fighting the flu.

Keep yourself healthy this flu season and be sure to take preventative measures. Your family and co-workers will be thanking you for not getting them sick.

Thank you for your time and attention.  Let’s make it safe this Monday.

Phil Kwitek

Demand Generation Specialist, Lift’n Buddy, a Southworth Company

Harvest Time Driving Safety

MAKE-IT-SAFE MONDAY

It’s that time of year again. The leaves are changing, and farmers are starting to harvest their crops. This increase in large equipment on roadways, leads to an increase in accidents in farming communities.  A study at Iowa State has shown that almost half of all collisions involving farm vehicles happen from October through November. 

The most common of these collisions occur when a distracted driver runs into the rear end of a farm vehicle, or when a passing motorist hits a farm vehicle trying to make a wide left turn. Data by the Iowa Department of Transportation shows that collisions involving farm vehicles are five times more likely to produce a fatality than any other type of motor vehicle accident. This is why drivers need to be on the lookout for farm vehicles.

Many motorists do not know the limitations of large farm vehicles. In order to make a wide enough left turn, the equipment operator might need to turn to the right slightly. Motorists see this slight right turn and assume the farm vehicle driver accidentally signaled to go left when they meant to signal right. This causes impatient motorists to begin to pass the farm vehicle only to have that vehicle start to turn left, and cause a collision. 

Farm equipment lighting may also not be very well maintained, especially the rear lighting. This may also contribute to rear end collisions. Motorists driving late at night might not notice the farm vehicles. 

Farm machinery travels slower than normal traffic, often at speeds of 25 miles per hour or less. Automobile drivers need to quickly identify farm equipment and slow down to avoid rear end crashes.  It is a good idea to stay back at least 50 feet so you remain visible to the equipment operator.

Vehicles aren't the only thing that drivers need to be aware of. The harvesting of crops like corn disturbs the habitat of wild animals. Deer are the leading cause of animal related car accidents. Motorists should be on the lookout for deer that are moving at this time of year.

To avoid accidents during the harvest season, keep an extra eye on the road, and always be patient when driving near farm vehicles.

Thank you for your time and attention.  Let’s make it safe this Monday.

Lucas Wertish
Demand Generation Specialist, Lift’n Buddy, a Southworth Company

National Recovery Month

MAKE-IT-SAFE MONDAY

Millions of people around the world deal with mental illness and substance abuse on a regular basis. Chances are you have a co-worker, family member or friend that has suffered from a mental illness or dependency issues with alcohol or drugs. Vincent van Gogh, Winston Churchill and Abraham Lincoln are just a few of a long list of famous individuals that have struggled with mental disorders. September is National Recovery Month and today on Make-It-Safe Monday we would like to raise the awareness of those suffering from mental illness and substance abuse.

Mental illness is not fully understood by the medical community but most believe that it is caused by a combination of genetics, brain injuries, infections, drugs or alcohol. An abnormal balance of chemicals in the brain will inhibit certain nerve cells from sending messages correctly from different areas of the brain. Drugs and alcohol can also temporarily and permanently change the chemistry and damage nerves in the brain. This can cause severe anxiety and social isolation which can lead to depression. If not treated, it can eventually lead to individuals harming themselves and others.

It may not always be easy to tell if some has a mental illness or substance abuse problem but if you see some of the following characteristics from someone you are around on a daily basis it might be in both of your best interest to approach the subject of seeking treatment.

• Social withdrawal
• Difficulty preforming familiar tasks
• Problems with concentration or memory
• Loss of initiative
• Dramatic sleep and appetite changes
• Mood swings
• Suicidal thoughts or tendencies

It is very important to seek help for a co-worker or friend that has suffers from mental illness.  It is extremely dangerous in certain situations to work with an individual that could cause serious harm to themselves or others. There are many organizations and professionals on the local and national level dedicated to helping with recovery.  The Substance Abuse and Mental Health Services Administration (SAMHSA) is a federal government organization dedicated to prevention, treatment and recovery. SAMHSA offers dedicated national helplines (1-800-662-HELP) and the SAMHSA.gov website provides multiple links to online resources and local treatment centers.

Mental health is a serious issue that needs our full attention. The recent increase in school and work place shootings is a reminder that it is of the utmost importance that we recognize the warning signs of the people around you. With proper care and treatment roughly 90% of adults are able to lead happy and fulfilling lives.

Thank you for your time and attention. Let’s make it safe this Monday.

Brad Lindemann

Sales Coordinator, Lift’n Buddy, a Southworth Company

There is NOTHING More Important Than Safety in the Workplace

MAKE-IT-SAFE MONDAY

In a couple short weeks (11 days to be exact at the time of this writing) Lift'n Buddy, A Southworth Company, will attend the National Safety Council Congress and Expo in Chicago, Illinois.  This event not only allows us to showcase our innovations, but to go shoulder-to-shoulder with what is new in safety, industry regulations and policies, and to get all the necessary inputs to be on the cutting edge of safety in the workplace.  Afterall, there is nothing more important than safety in the workplace.  It's about saving lives!  Check out the following youtube video on this event and see the info from the NSC website below:

http://www.youtube.com/watch?v=HpC3x5IzvAo#t=42

About the event

The NSC Congress & Expo is the world's largest annual "must attend" event for safety, health and environmental professionals. For more than 100 years, professionals have turned to this event for industry-leading technology, education, networking opportunities and the tried and true products and services needed to stay at the forefront and remain competitive within the industry.

In 2010, NSC introduced the Journey to Safety Excellence philosophy, which can help you and your company answer the following questions regarding its current safety program:

• Where are you now – and where do you want to be?
• How will you move forward?
• How do you manage your improvement and measure your progress?

Congress is designed to build awareness of the tools available to you and your organization as you continue down the path to safety excellence.

The NSC Congress & Expo experience offers:

• Educational Opportunities
  Attendees don't have to hunt through blogs for perspectives on trends and best practices - they can choose from a host of carefully selected opportunities led by verified safety experts. And because safety challenges come in all shapes and sizes, presenters make time for Q&A at the end.
  • Keynotes
    Hear nationally recognized leaders and motivational s from both the public and private sectors speak about current and future issues affecting the industry.
  • Technical Sessions
    Participate in more than 130 technical sessions, selected by a team that has hands-on knowledge of the latest industry trends providing the most comprehensive information needed to face today's challenges.
  • Professional Development SeminarsParticipate in more than 30 seminars providing in-depth, hands-on opportunities to focus on continued professional growth.
• The Expo Floor:  With both employee safety and budget-friendliness in mind, attendees can compare vendors for a particular product in one place over the course of three days. The time and energy put into researching options is minimized - and face-to-face communication ensures questions are answered and needs are met.
• Explore the Expo floor offering 190,000+ net square feet of more than 900 companies showcasing the latest innovative products and services. You'll also find the New Product Showcase area, the Solution Center, OSHA's Top 10 most cited safety violations and solutions from the International Safety Equipment Association.
• Networking EventsNetwork and unwind with like-minded professionals during Rock 'n' Community: Connections for a Cause and the National Awards Celebration.

Who attends and why?

The NSC Congress & Expo attracts decision makers, end users and distributors from a wide variety of industries including: manufacturing, construction, petrochemical and utilities. Coming from the United States, Canada and more than 60 other countries, these individuals range in experience from entry level to seasoned safety professionals representing companies such as Boeing, Schneider Electric, BP, Industrial Scientific, Kimberly Clark, URS, RockTenn Norcross, Fruit of the Loom and more.

Who exhibits?

Hundreds of industry-leading companies from around the world exhibit offering products and services in the following categories: general safety products, personal protective equipment, hazard controls and fall protection. Additionally, vendors specializing in facility maintenance and operation, environmental protection, ergonomics and risk management are in attendance to showcase their latest safety solutions. The show not only features large companies such as Honeywell, 3M and Grainger but hundreds of small to mid-size companies.

Come and visit us at Booth #526, and see how Lift'n Buddy is an agent for change in the modern day workplace. In the meantime check us out at liftnbuddy.com and LIKE us on Facebook.

Thank you for your time and attention. Let’s make it safe this Monday.

Aaron Lamb
General Manager, Lift'n Buddy , a Southworth Company